ATTENTION
BUILDERS...
Call for special pricing on
multiple gallons!
A premium spray-on insulation for all cars and trucks, street rods
and customs, race cars, buses, refrigerated trailers, RVs,
motorhomes, experimental aircraft, and high end audio
installations---wherever heat and noise are a problem.
LizardSkin® Ceramic Insulation formula is
an advanced, water-based composition of high-grade acrylic binders
with air-filled insulating/reflective and sound-absorbing
particles.
 | Environmentally friendly, water-based |
| Class A fire-rated |
| No respirator needed; dust
mask/protective eyewear recommended |
| Spay application only; brush for small
areas or touch up. |
| Can cover hard to reach places like
inner door panels |
| Cleans up with soap & water |
| Each 2-gallon container covers 46-50
sq. feet @ .040” |
Proven aerospace technology enables
LizardSkin® Ceramic Insulation to:
| Reduce engine and solar heat transfer
by 25-30 degrees or more |
| Reduce noise by 10-12 decibels or more |
| Protect surfaces from moisture and
corrosion |
| Withstand temperatures to 500° F.
(260° C.) |
LizardSkin Ceramic Insulation
50100 - 2 Gallon Pail
LizardSkin Coverage
Guidelines:
|
Typical vehicle coverage scenarios |
|
Vehicle |
Ceramic
Insulation |
Older style Pickup
1940-1960 |
2
gal. - 1 unit |
| 3-5 Window Coupe |
4
gal. - 2 units |
2-door Sedans
1933-1939 |
6
gal. - 3 units |
Chevy/Ford
1955-1957 |
8
gal. - 4 units |
How to
calculate gallons needed:
| Measure length x width of all surfaces
to be coated |
| Add all numbers for total area in
square feet |
| Divide by 25 for LizardSkin® Ceramic
Insulation or by 50 for gallons of LizardSkin® SC needed
|
Note: If spraying LCI on
both interior and exterior floor, spray .020 on interior floor,
and .020 on exterior floor to achieve .040 total. Recommended LCI
thickness: 40 to 60/1000ths. Recommended LSC thickness: 20 to
25/1000ths.
Typical
Uses:
LizardSkin® Ceramic
Insulation is used by custom car, street rod, race car and truck
builders as well as RV owners to reduce heat and noise transfer
and seal unexposed body surfaces. When applied under fender wells,
it can help prevent “starring” from stones and gravel. It is best
applied with our special spray gun to a clean and dry primed or
painted rust-free surface. Typical applications include firewalls,
floor pans, transmission tunnels, doors, hoods, truck lids, under
headliners, inside fenders, panel van walls and more. It may be
painted if desired, with no loss of thermal or acoustic
performance.
Important: Manufacturers Recommendations:
For best results,
LizardSkin must be applied with a recommended spray gun/nozzle at
50-70 psi air pressure. For specific recommendations, consult
product label. Brushing is recommended only for small area touch
up.
Typical Tools
Required:
| LizardSkin® Super Pro spray gun kit |
| Variable speed 3/8”-1/2” electric
drill |
| Box cutter or knife |
| Compressed air source: 60-100 psi @ 5
cfm(min |
| Access to
water for cleanup
|
Surface Preparation:
Surface to be coated must
be clean, dry and free of rust or other corrosion. Mask areas not
intended to be sprayed since coating will adhere to any unmasked
area. Carbon steel surfaces require primer. Aluminum and stainless
steel do not need primers but must be clean and dry.
Product
Preparation/Mixing:
LizardSkin® should be mixed
thoroughly using a power drill with the mixer paddle bit.
| Open the container using the tear tab
on the side of the top. |
| Pull tab and remove lid. |
| Mix LizardSkin® using variable speed
drill and stir paddle bit at low rpm (300 or less) to a smooth
consistency. (Normally 2-4 min.) |
| Clean stir
paddle in water bucket immediately after mixing. Replace lid on
bucket until ready to spray. |
| After mixing, lift mix paddle from
LizardSkin. If product drips off slowly, it is ready to apply. |
 LizardSkin®
SC formula is an advanced, water-based composition of high-grade
acrylic binders with sound-damping particles. Proven sound damping
technology enables LizardSkin® SC to dramatically reduce noise
when properly applied. It also protects surfaces from moisture and
corrosion and can withstand temperatures to 300° F. (149° C.)
LizardSkin® SC is used by custom car,
street rod, truck builders and RV owners who want to reduce
unwanted noise and/or enhance the sound of their high end audio
systems. It is best applied by special spray gun to a clean and
dry primed or painted rust-free steel. Typical applications
include firewalls, floor pans, transmission tunnels, doors, hoods,
trunk lids, under headliners, inside fenders, panel van walls and
other areas that generate vibration and noise. For maximum
acoustic performance, coat entire interior surface and the floor
inside and out.
| Dramatically reduces noise and
vibration |
| Protect surfaces from moisture and
corrosion |
| Withstand temperatures to 300° F.
(149Ş C.) |
| Class A Fire-rated |
| A 2- gallon container covers
approximately 100 sq. ft. at 20/1000's (Max thickness 40/1000's
for maximum effectiveness) |
Applying
LizardSkin® Ceramic Insulation & LizardSkin® SC
For maximum sound control and insulation performance, both
LizardSkin coatings may be used, but it is important that
LizardSkin® SC always be applied FIRST. When used in tandem,
LizardSkin® SC should be applied at least 12 hours prior to
application of LizardSkin® Ceramic Insulation. |
LizardSkin Sound Control
50115 - 2 Gallon Pail
 The SuperPro
spray gun kit provides exactly what’s needed for professionals and
hobbyists to properly apply amazing LizardSkin® coatings Typical
spray guns used for paint application are simply not engineered to
handle the higher density of these high technology coatings. To
help facilitate this process for builders and manufacturers,
LizardSkin LLC is pleased to offer the proven quality of the
SuperPro spray gun.
| Professional quality spray gun
designed to handle the high density and viscosity of LizardSkin®
Ceramic Insulation and LizardSkin® SC – Sound Control Formula
with extra nozzles and flexible spray wand for hard to reach
areas. |
| Included one-quart cup can be used for
application to small areas |
| One stir paddle (attaches to drill) |
| One 48” siphon hose (5/8 Inch ID Thick
Wall Rubber) |
| One 12-inch siphon tube (1/2 Inch ID,
5/8 Inch OD Metal Conduit) |
| Two hose clamps, one threaded hose
barb |
| LizardSkin coatings should not be
applied when ambient temperature is below 70 degrees. |
LizardSkin Super Pro Spray Gun Kit
50125 - 1 Kit
|
 |
 |
 |
| |
Insulation
Insulation supplied
by
LizardSkin®
|
|
 |
 |
 |
2520 Allen Road South
Charlotte, NC 28269
(800) 529-0232
(704) 599-0232
|
LizardSkin®
Ceramic Insulation