Get your free quote by calling

(800) 529-0232

Wiring & Electrical

Complete Wiring Kits

Chevy Powered Bare Bonz Wiring #BB-99 

$359.95 

This kit includes headlight switch, plugs for GM and aftermarket columns, all wiring needed for most safety inspections, gauges, complete Chevy engine, printed and color coded fire resistant wire and our famous color coded instructions.  This kit has 8 fuses and 10 circuits that employ our latest Direct Wire System including super quality for simple applications.  Set up for ONE WIRE alternators.  Accepts GM TPI and LT-1 fuel injection easily.  We don’t use an old GM fuse block and say it will work.  We do it right this panel measures only 7-3/4 L x 3-3/8 W x 2-7/8 H. 

Ford Powered Bare Bonz Wiring #BB-78 

$359.95 

This kit includes headlight switch, plugs for GM and aftermarket columns, all wiring needed for most safety inspections, gauges, complete Chevy engine, printed and color coded fire resistant wire and our famous color coded instructions.  This kit has 8 fuses and 10 circuits that employ our latest Direct Wire System including super quality for simple applications.  Set up for ONE WIRE alternators or we can make changes to accept yours.  Accepts fuel injection easily.  We don’t use an old GM fuse block and say it will work.  We do it right this panel measures only 7-3/4 L x 3-3/8 W x 2-7/8 H.

We carry the full line of wiring kits from lights to fuel injection wiring. 
Give us a call for all your electrical needs.

Highway 22 Modular Panel System

Modular wiring system.  Part No# 500695 

$429.00

22 power circuits supported through 15 fuses and 1 circuit breaker.  Battery and accessory power tap studs provided for system expansion.  Panel protected with a 175 amp Mega-Fuse junction block with a 8 gauge panel feed wire.  Nylon mechanically secured panel containing secondary  push-back locks, has a 7-1/2” x 4-1/2” footprint, 3-3/8”in height, and mounted on a (G10) non conductive epoxy base.  All power buss bars are constructed of 6 gauge copper.  All wires are constructed from heat resistant (-60F- +275F).  GXL heavy-wall wire with laser printed circuit identification every 2 inches.  GM color coded wires for ease of installation.  All power circuits wires are 12 gauge constructed.  New front loaded vibration proof self-locking (Hooke’s Law) screw down terminal connection.  Dedicated battery and ignition circuits for electronic fuel injection (EFI) Kit contains 3 relays (Horn, Turn Signal & 40 amp Electric Fan or Fuel Pump).

Turn signal and hazard flasher circuits provided.  8 gauge alternator feed wire provided.  The kit is set-up for a GM “SI” internally regulated alternator or GM 1-wire.  Alternator diode is also provided.
Kit includes 3 (In-dash Ignition, Headlight & Alum. Knob and Floor Dimmer) switches.  GM in-column ignition switch connectors provided, along with 3-7/8” GM steering column connectors with male and female terminals.

Plugs directly into most 69-74 GM column and most after market steering columns or use the terminals and connector provided to mate to any column.  Spare circuits available (for power windows, locks, cruise, etc.).  Engine compartment (oil pressure, water temp, tach, starter, neutral safety, brake switch, ignition switch, distributor (GM HEI or Points), coil, main power and alternator).
Chassis wiring (fuel pump, electric fan, headlights, running lights, brake lights, 3rd brake light, directional, license plate, radio, heat & AC, and wipers).  Full color schematic of overall vehicle wiring along with individual harness subkit instructions for trouble-free installation.

Highway 15 Modular Panel System

Modular wiring system.  Part No# 500703 
$319.00

The Highway 15 is a brute in a small package. Built with the same heavy duty internal components as those used in our Highway 22 panel, it can easily handle the "basic "power requirements of any vehicle. Its size makes it the perfect power center for roadsters, T- buckets, kit cars, race cars or any other vehicle where basic operational circuits are required. Heavy gauge lead wires are provided for battery, ignition, accessory, horn, turn signal flasher, and 4-way hazard flasher. Best of all, it is also designed around the same "cook book "installation approach employed with all of our systems. Easy clamp-style system makes adding and removing wires easy! No Terminals! No Crimping! No Screws!

Ignition switch Included.  Connections included for either dash or column mounted ignition switches.
All needed terminals and connectors to finish the basic wiring system are included.
Complete wiring for headlights (Headlight switch included with internal circuit breaker).
Mounting legs are moveable to allow for various mounting situations.  Alternator regulator diode included.  Micro-Relays for Horn and signals.  15 output connections.  Floor mounted dimmer switch Included.  Heat resistant nylon 6/6 construction throughout.  3 position head-light switch.  Designed with internal circuit breaker protection (Billet knob included).  Unique design of "gauge cluster disconnect ". Makes connecting up to 8 gauges simple and convenient. Heavy 8-Gauge alternator power feed wire.  High heat and abrasion resistant XLPE wire. (Wire withstands -60oF to +275°F).
 

Complete engine compartment wiring for oil pressure, water temperature, starter, neutral safety switch, ignition switch, distributor coil, main power feed, alternator and regulator.  Coil leads supplied with connector for GM HEI distributor.  Bypass wire included for point type distributors.  Headlight circuit complete with circuit breaker for headlight switches without integral circuit breaker. 

Complete wiring for all running lights, brake lights and directional lights, and license lights and third brake lights.  Dash wiring included for electric gauges such as oil pressure, water temp., voltmeter, fuel gauge, and tachometer. Dash lighting for all gauges, speedometer, turn signal & high beam indicator lights. 

Complete wiring for steering column including horn, directional signal switch and 4-way hazard switch. Standard 3-7/8" GM column connector (both male and female) are provided to directly plug-in to any .69-.74 GM steering columns. Connector bodies and terminals are provided to also make mating to any make column a breeze.

Complete wiring for radio, heat and A/C, and wipers.  Spare battery and accessory circuits.  All fuses, flashers, and relays included.  Horn relay on panel.  Standard turn signal and hazard flasher circuits.  Circuit breaker capability on 1 battery and 1 accessory circuit  Wire circuit ink-jet labeling every 2 "or 3 ".  Heavy duty terminals and internal power buss.  Rugged factory terminals and terminations within the fuse panel assembly.  Color schematics and easy to understand installation instructions included.  Patented Hooke’s Law Screw-down connection system.

22 Circuit Street Rod Harness

Great for Street Rods, Rat Rods, Race Cars and even in your Dune Buggy.  For any hot rod or restoration project you need to wire. 

22 Circuit
Universal Street Rod Harness includes:

High / Low Beam, Parking Lights, Gauge Power / Interior / Dash Lights, Turn Signal / Hazard Lights, Brake Lights, Horn / Cooling Fan Circuit, Ignition/Coil/Distributor, Starter Circuit, Charging / Alternator, Circuit Wipers, Fuel Pump, Radio / Accessory (Constant Hot), Radio / Accessory (Ignition Hot), AC/Heat Power & Fan, Pre-wired Neutral safety, Power Antenna, Power Windows, Power Door Locks, Cruise Control, Cigarette Lighter, (2) Auxiliary Connections

20 ATC Fuses, Speaker Wire included in harness, Engine Kill Switch at fuse block, Pre-wired Flasher Unit, Pre-wired Hazard Unit, Pre-wired Horn Relay, Compact easy to hide design, Pre-wired turn signal circuit, All connections crimped and hand soldered for reliability, Aluminum base for a solid installation, Brushed steel fuse cover, All wires labeled by circuit & color coded to match GM factory wiring color codes, Instruction Booklet, Toll Free Phone Tech Support.

22 Circuit Harness 

$240.00

22 Circuit w/Ground 

$265.00

22 Circuit w/Switches 

$295.00

14 Circuit Street Rod Harness

Great for Street Rods, Rat Rods, Race Cars and even in your Dune Buggy.  For any hot rod or restoration project you need to wire.  14 Circuit
Universal Street Rod Harness includes:

14 Pre-wired and Fused Circuits, Pre-wired Fuse Panel, Lighting Group, High / Low Beam / Parking Lights, Turn Signal, Hazard Lights, Horn, Cooling Fan Circuit, Interior Group, Gauge Power, Interior Lights, Dash Lights, Radio (Constant), Radio (Switched), Wipers, A/C - Heater Fan, Motor Group, Neutral Safety, Coil, Distributor, Choke, Horn, Tail Group, Brake Lights, Fuel Pump, Fuel Gauge, Parking/Turn lights, Electric Fan

12 ATC Fuses, Speaker Wire included in harness, Engine Kill Switch at fuse block, Pre-wired Flasher Unit, Pre-wired Hazard Unit, Pre-wired Horn Relay, Compact easy to hide design, Pre-wired turn signal circuit, All connections crimped and hand soldered for reliability, Aluminum base for a solid installation, Brushed steel fuse cover, All wires labeled by circuit & color coded to match GM factory wiring color codes, Instruction Booklet, Toll Free Phone Tech Support.

14 Circuit Harness 

$210.00

14 Circuit w/Ground 

$235.00

14 Circuit w/Switches 

$265.00

8 Circuit Street Rod Harness

Great for Street Rods, Rat Rods, Race Cars and even in your Dune Buggy.  8 Pre-wired and Fused Circuits.  8 Circuit Universal Street Rod Harness includes:

Fuse Panel Pre-wired for High / Low Beam / Parking Lights, Gauge Power / Interior / Dash Lights,    Turn Signal / Hazard Lights, Brake Lights, Horn / Cooling Fan Circuit, Coil/Distributor/Choke, Fuel Pump, Radio, Wipers, Electric Fan

50 AMP Main Fuse (instead of fusible link), 8 ATC Fuses, Speaker Wire included in harness, Engine Kill Switch at fuse block, Pre-wired Flasher Unit, Pre-wired Hazard Unit, Pre-wired Horn Relay, Compact easy to hide design, Pre-wired turn signal circuit, Only high temperature and crack/oil resistant GXL wire is used -60 to 275 F, All connections crimped and hand soldered for reliability, Aluminum base for a solid installation, Brushed steel fuse cover, All wires labeled by circuit & color coded to match GM factory wiring color codes, Instruction Booklet, Toll Free Phone Support.

8 Circuit Harness 

$195.00

8 Circuit w/Ground 

$220.00

8 Circuit w/Switches 

$250.00

Switches

Headlight Switch with Billet Knob

Part # 70701-A  $27.50

4.5 Ohm Dimmer, 15A at 12V Internal Circuit Breaker. With black knob imprinted with SEA headlamp symbol. Connector and terminals included.  Billet knob will give your street rod a custom look. Billet knobs can also be purchased separately.

Master Disconnect Switch

Part No#1005  $36.00

Disconnects Alternator and Battery DPST (on-off).
Breaks alternator circuit (maximum of 20 amps) prior to disconnecting battery.  3/8” and #10-32 stud terminals.

Cooling Fan Sensor System Relay
30 Amp Fused Relay, Part No#AR-35  $29.95

Ignition Switch Activated without AC Request

These proven units supply the absolute best protection for your vehicle when using electric cooling fans. All include 30 amp fuses and high quality relays to carry the high amperage and provide the full battery voltage with top quality wiring, while eliminating the heavy load on the car's ignition switch. All units have highly reliable thermostats except the AR-35 which simply operates whenever the key is on or via manual switch. AC request option turns on the fan when the AC compressor is engaged. Sensors have 3/8 inch pipe thread.

The temperature sensor is designed to be mounted in the cylinder head. If this location presents a problem due to headers or exhaust manifolds it can be located in the intake manifold. Doing so however can effect sensor switching temperature as much as +15 degrees. Order the lower sensor temperature (On 176/Off 161) for the fan to turn on approximately 190 degrees.

The temperature sensor is designed to be mounted in the cylinder head. If this location presents a problem due to headers or exhaust manifolds it can be located in the intake manifold. Doing so however can effect sensor switching temperature as much as +15 degrees. Order the lower sensor temperature (On 176/Off 161) for the fan to turn on approximately 190 degrees.

These proven units supply the absolute best protection for your vehicle when using electric cooling fans. All include 30 amp fuses and high quality relays to carry the high amperage and provide the full battery voltage with top quality wiring, while eliminating the heavy load on the car's ignition switch. All units have highly reliable thermostats except the AR-35 which simply operates whenever the key is on or via manual switch. AC request option turns on the fan when the AC compressor is engaged. Sensors have 3/8 inch pipe thread.

The temperature sensor is designed to be mounted in the cylinder head. If this location presents a problem due to headers or exhaust manifolds it can be located in the intake manifold. Doing so however can effect sensor switching temperature as much as +15 degrees. Order the lower sensor temperature (On 176/Off 161) for the fan to turn on approximately 190 degrees.

Universal Floor Dimmer Switch

Part No# DS-02 

$12.95

With Switch Housing & Terminals, Part No# DS-03 

$15.95

Firewall Stud Insulator

Perfect for passing battery cables through firewall or other panels.  Mounting hole size 1-1/4”.

FS-7 Black Cap 

$20.95

FS-8 Red Cap 

$20.95

Courtesy Light Kit

Part No# EX-7  $42.95

Great plug-in accessory that positions two lamps under corners of the dashboard.  Controlled by turning headlight switch knob and/or door jamb switches.  Special sockets/brackets and bulbs included. 

Order Door Jamb switches separately based on your needs.

Anti-Theft Relay Wiring Kit

Part No# AT-70  $56.95

These kits wire directly to your panel so the vehicle will not crank until something else in the car is turned on, such as parking lights, headlights, brake lights, a hidden switch or whatever item you choose.  Includes an advanced circuit to blow your horn if the selected task is not completed in the proper order.

Door Jamb Switch

Part No# DJ-23  $12.95

Replacement switch for Ford applications.  If your switch looks close to this it should be the right one.  Uses a 29/32” mounting hole.

Part No# DJ-26  $16.95

This switch requires NO ground to the body.  It can be used in fiberglass applications or where grounding can be a problem.  The self tapping thread will work well and the exposed shaft will self adjust to the door jamb thickness when you close the door the first time.  Uses a 7/16” mounting hole.

Part No# DJ-24  $11.95

For universal application, on metal bodies only.  The self tapping thread will work well and the exposed shaft will adjust to the door jamb thickness when you close the door the first time.  The button end will collapse to the thickness of the button itself.  This switch is “self tapping” and uses an 11/32” mounting hole.

Part No# DJ-16  $14.95

Universal switch made with two contacts.  For use in fiberglass cars or vehicles that need to run ground wire to ensure the connection.  Uses a 23/32” mounting hole.

Dash Gauge Wiring Kit

Part No# DK-6  $67.95

The perfect solution for those who would like the gauge cluster to unplug for easy installation and maintenance. The kit includes special disconnect plug(s) for dash gauge wiring with terminals for most type gauges and eliminates the need for most splicing. The kit really cleans up the dash wiring. Detailed instructions and printed wires for use with or without our wiring kit.

Use the DK-6 to fit most Classic, Stewart-Warner, Sun, Autometer and older VDO gauges. DK-8 have polarized connectors for exact fit to all new VDO gauge packages.

Wiring included for Dash Lights, Indicator Lights (Turn/High/Low Beam), Fuel Gauge/Sender, Oil Gauge/Sender, Temp Gauge/Sender, Tachometer, Electronic Speedometer, DK-6 also includes a Miscellaneous Gauge.

Gear Shift Indicator Sets

Available in horizontal and vertical 1” x 3” patterns.  Overdrive transmissions will have the extra “OD” light.  All are engraved and have self-adhesive backing.  Brushed Silver Face.  Indicator lights included.

P-R-N-D-L2-L Vertical,

Part No#GP-9 

$34.95

P-R-N-O-D-2-1 Vertical,

Part No#GP-10 

$34.95

P-R-N-D-L2-L Horizontal,

Part No#GP-11 

$34.95

P-R-N-O-D-2-1 Horizontal,

Part No#GP-12 

$34.95

Dash Indicator Set

Brushed silver with engraving and self-adhesive backing.  Both sets have green LEDs for turn indicators.

Blue High Beam Indicator,

Part No#LB-7 
$29.95

Red High Beam Indicator,

Part No#LB-5 

$28.95

Grounding Terminal Strip

Part No#GW-15  $24.95

This terminal strip is absolutely the best way to create common grounds for fiberglass cars and metal cars you want to do correctly.  A heavy printed feed wire is connected to the battery ground for best results.  Ten (10) screws for smaller grounds and two (2) studs for larger connections.

Dash Lights

Small LEDs with black bezel and 6” wire leads.  Mounting hole size is .156 inch (use 5/32” drill bit for proper installation).

Red, Part No# DR-16  $6.95

Amber, Part No#DA-16  $6.95

Green, Part No#DG-16  $6.95

Blue, Part No#DB-16  $8.95

Medium indicator lights with chrome bezel and 6” wire leads.  Mounting hole size is 5/16”.

Red, Part No# DR-32  $8.50

Amber, Part No#DA-32  $8.50

Green, Part No#DG-32  $8.50

Blue, Part No#DB-32  $8.50

Large indicator lights with chrome bezel.  Mounting hole size is 1/2”.

Red, Part No# DR-50  $10.95

Amber, Part No#DA-50  $10.95

Green, Part No#DG-50  $10.95

Blue, Part No#DB-50  $10.95

Turn Signal Switch

Part No#SS-1  $45.95

Standard mounting nut.

Grommet Assortment

Part No#GA-10 (28 pieces)  $15.95

Assortment of 8 sizes, 4 of 1/4, 5/16, 3/8, 7/16, 1/2 and 5/8.  2 of 7/8 and 1”.

Expandable Firewall Grommet

Part No#GA-20 (4 pieces)  $11.95

Rubber firewall grommets 1.25” O.D. Inner hole size .625.  The thinner center will ‘give’ to open up and allow more wires to pass yet keep a tighter seal.

2520 Allen Road South

Charlotte, NC 28269

(800) 529-0232

(704) 599-0232

[ AC Kits & Components ] [ Bodies, Fenders & Parts ] [ Brake Kits & Components ] [ Chassis Components ] [ Camaro Components ] [ Complete Chassis ] [ Cooling Components & Fans ] [ Custom IFS Front Ends ] [ Engine Accessories ] [ Engine Mounts ] [ Front Suspension ] [ Fuel Tanks ] [ Gauges & Inserts ] [ Headers ] [ Headlights & Tail Lights ] [ Interior Trim ] [ LizardSkin Insulation ] [ Mustang II Front Ends ] [ Nova Components ] [ Power Windows & Entry Kits ] [ Radiators ] [ Steering Components ] [ Steering Wheels ] [ Suspension Components ] [ Transmission Crossmembers ] [ Wheels ] [ Wiring & Electrical ] [ eBay Store ] [ About Us ] [ Order Form ]

2520 Allen Road South, Charlotte, NC  28269